为您找到"
SLEEPCMD &= ~OSC
"相关结果约100,000,000个
The same SLEEPCMD register issue exists with the CC2540. Version 1.1 of the CC2540 Bluetooth Low Energy Software Development Kit (CC2540 BLE v1.1) references OSC_PD as bit-2 of the SLEEPCMD register in the hal_board_cfg.h and hal_mcu.h files. The User's Guide shows bit-2 of the SLEEPCMD register as Reserved (reference page 63 of SWRU191B (Sep ...
其次，OSC_PD=0X04这句话是根据宏定义来推算出来的，并没有错误 最后，我的问题是，我需要正确的SLEEPCMD各个位的不同的值代表什么意思。 附录：给你看看底层文件的宏定义，你可以自己推算一下 #ifndef BV #define BV(n) (1 (n)) #endif #define OSC_PD BV(2)
Harassment is any behavior intended to disturb or upset a person or group of people. Threats include any threat of violence, or harm to another.
This is still a duplicate. The answer on the dupe even states, "It seems that sleeping a computer is problematic if hibernate is turned on. The command rundll32.exe powrprof.dll,SetSuspendState 0,1,0 for sleep is correct - however, it will hibernate instead of sleep if you don't turn the hibernation off," and it even suggestions a solution - using PsShutdown which does support either suspend ...
Problem with rundll32.exe powrprof.dll,SetSuspendState 0,1,0 is that IT DOES NOT WORK as it should.SetSuspendState will put the computer into a sort of Hybrid Sleep/Hibernation mode. When you use the Sleep button from the start menu, you can resume your computer from sleep by pressing a any key on your keyboard.
我想问的是cc2530中的寄存器sleepcmd中的各个位都是什么意思?好像跟我po上的图不一样； sleepcmd &= ~osc_pd;这句话的意思是把sleepcmd的第二位给置0；可是我上面的图第二位写的是保留. 我下载的资料可能有点错误；请教一下各位大神给我介绍一下. 这个设置是可以满足 ...
zigbeecc2530中语句：sleepcmd&=~osc_pd；为什么8位寄存器sleepcmd能与它自身第二位的osc_pd进行位与操作？ ZigBee CC2530中 语句：SLEEPCMD &= ~OSC_PD； 为什么8位寄存器SLEEPCMD能与它自身第二位的OSC_PD进行位与操作？
SLEEPCMD 是睡眠srf啊，怎么注释是turn on 16MHz RC and 32MHz XOSC ，好像不对啊，我的程序一直在while (!(SLEEPSTA & XOSC_STB)); 跳不出来，SLEEPSTA 值是0x26. 不知道怎么回事
Hi, hec How r u. Some problems about the specification of SLEEPCMD/SLEEPSTA were found when I read the Basic RF programs. 1. In the User Guide of "CC253x
文章浏览阅读6.4k次，点赞4次，收藏34次。这篇博客介绍了cc2530芯片在休眠模式下的配置，包括pm0到pm3四种模式的设置，重点讨论了外部中断和睡眠时钟中断的唤醒机制。通过实例代码展示了如何进入pm3和pm2模式，并利用外部中断和睡眠定时器进行唤醒。实验中，设备在led闪烁后进入相应休眠模式 ...